The influence of cracks on the salt scaling resistance and chloride ingress in recycled aggregate concrete

Authors

DOI:

https://doi.org/10.62638/ZasMat2004

Abstract

Recycled concrete aggregate (RAC) offers a promising solution to reduce raw material use, energy consumption, and waste. However, its durability remains a concern. Due to low tensile strength, cracking under load is likely, which can impact concrete's longevity. In this paper the influence of loading induced cracks (0.08 mm and 0.20 mm) on RAC resistance to salt scaling and the impact of previous carbonation on their resistance to salt scaling was presented. The influence of cracks on the development of reinforcement corrosion on long probe as well as corrosion mapping in relation to the position of the crack was analyzed. The onset and the development of corrosion process on steel reinforcing probes were monitored by three different electrochemical techniques: open circuit potential monitoring, electrochemical impedance spectroscopy and linear polarization resistance. It was shown that the presence of cracks on the concrete surface will increase the salt scaling resistance, and beside the crack width, a number of cracks proved to be an important factor influencing concrete resistance to salt scaling. Previous carbonation of RAC decreases the salt scaling resistance of concrete for more than 2.5 times. The reinforcing steel surface close to the crack started to corrode quickly, at the first day of exposure to chloride rich environment. The steel bars far from the crack (35 mm and 55 mm distances), remained in passive state in RAC with 20 mm concrete cover, even after 160 days of exposure to 3 % NaCl electrolyte.

Keywords:

recycle aggregate concrete, cracks, salt scaling, carbonation, corrosion

References

S. Marinković, J. Dragaš, I. Ignjatović, and N. Tošić, “Environmental assessment of green concretes for structural use,” J. Clean. Prod., vol. 154, pp. 633–649, 2017.

B. J. Pease, “Influence of concrete cracking on ingress and reinforcement corrosion,” Technical University of Denmark, 2010.

M. Otieno, H. Beushausen, and M. Alexander, “Chloride-induced corrosion of steel in cracked concrete - Part I: Experimental studies under accelerated and natural marine environments,” Cem. Concr. Res., vol. 79, pp. 373–385, 2016.

A. Blagojevic, “The Influence of Cracks on the Durability and Service Life of Reinforced Concrete Structures in relation to Chloride - Induced Corrosio A Look from a Different Perspective,” Delft University of Technology, 2016.

fib-Bulletin 34, Model Code for Service Life Design, 1st ed. Lausanne, Switzerland: International Federation for Structural Concrete (fib), 2006.

P. T. Nguyen, E. Bastidas-Arteaga, O. Amiri, and C. P. El Soueidy, “An Efficient Chloride Ingress Model for Long-Term Lifetime Assessment of Reinforced Concrete Structures Under Realistic Climate and Exposure Conditions,” Int. J. Concr. Struct. Mater., vol. 11, no. 2, pp. 199–213, 2017.

A. B. Harnik, U. Meier, and A. Rosw, “Combined Influence of Freezing and Delcing Salt on Concrete—Physical Aspects,” Durab. Build. Mater. Components, vol. ASTMSTP 69, p. 474–484., 1980.

G. W. Scherer, “Stress from crystallization of salt,” Cem. Concr. Res., vol. 34, pp. 1613–1624, 2004.

M. Yamamoto, K. Nakarai, Y. Yoshizumi, and R. Torrent, “Case Studies in Construction Materials Relationship between chloride ingress and concrete cover quality of inland structures exposed to deicing salts,” Case Stud. Constr. Mater., vol. 20, no. March, p. e03075, 2024.

J. J. Valenza II and G. W. Scherer, “Mechanism for salt scaling,” J. Am. Ceram. Soc., vol. 89, no. 4, pp. 1161–1179, 2006.

O. Çopuroǧlu and E. Schlangen, “Modeling of frost salt scaling,” Cem. Concr. Res., vol. 38, no. 1, pp. 27–39, 2008.

S. T. Pham and W. Prince, “Effects of Carbonation on the Microstructure of Cement Materials: Influence of Measuring Methods and of Types of Cement,” Int. J. Concr. Struct. Mater., vol. 8, no. 4, pp. 327–333, 2014.

C. Wang, J. Xiao, G. Zhang, and L. Li, “Interfacial properties of modeled recycled aggregate concrete modified by carbonation,” Constr. Build. Mater., vol. 105, no. February, pp. 307–320, 2016.

M. Leivo et al., “Effect of interacted deterioration parameters om service life of concrete structures in cold environments,” Espoo, Finland, 2011.

J. Z. Xiao, B. Lei, and C. Z. Zhang, “On carbonation behavior of recycled aggregate concrete,” Sci. China Technol. Sci., vol. 55, no. 9, pp. 2609–2616, 2012.

N. Otsuki, S. Miyazato, and W. Yodsudjai, “Influence of Recycled Aggregate on Interfacial Transition Zone, Strength, Chloride Penetration and Carbonation of Concrete,” J. Mater. Civ. Eng., vol. 15, no. 5, pp. 443–451, 2003.

S. Yehia, K. Helal, A. Abusharkh, A. Zaher, and H. Istaitiyeh, “Strength and Durability Evaluation of Recycled Aggregate Concrete,” Int. J. Concr. Struct. Mater., vol. 9, no. 2, pp. 219–239, 2015.

J. Xiao, D. Lu, and J. Ying, “Durability of Recycled Aggregate Concrete: An Overview,” J. Adv. Concr. Technol., vol. 11, no. 12, pp. 347–359, 2013.

J. Andal, M. Shehata, and P. Zacarias, “Properties of concrete containing recycled concrete aggregate of preserved quality,” Constr. Build. Mater., vol. 125, pp. 842–855, 2016.

Missouri Department of Transportation, “Project Title : Recycled Concrete Aggregate ( RCA ) for Infrastructure Elements Report C : Bond Behavior of Mild Reinforcing Steel in RCA Concrete” Rolla, Missouri, 2014.

X. Wang, “Evaluation of de-icer deterioration of concrete,” Iowa State University, Ames, Iowa, 2014.

M. Gomes, J. Brito, and M. Bravo, “Structural concrete with incorporation of coarse recycled concrete and ceramic aggregates: durability performance” Mater. Struct., vol. 42, no. 5, pp. 663–675, 2009.

J. Ying, J. Xiao, and Q. Meng, “On Probability Distribution of Chloride Diffusion Coefficient for Recycled Aggregate Concrete,” Int. J. Concr. Struct. Mater., vol. 10, no. 1, pp. 61–73, 2016.

L. F. Jimenez and E. I. Moreno, “Durability Indicators in High Absorption Recycled Aggregate Concrete,” Adv. Mater. Sci. Eng., vol. 2015, p. 8, 2015.

R. Movassaghi, “Durability of Reinforced Concrete Incorporating Recycled Concrete as Aggregate (RCA),” University of Waterloo, Ontari, Canada, 2006.

CEN, “EN 1992-1-1,” 1st ed., vol. 1, CEN, Ed. Belgrade: ISS, 2015.

R. Francois, I. Khan, H. Mercado, and A. Castel, “Influence of mechanical cracks on the development of corrosion mechanism,” in International RILEM Conference on Advances in Construction Materials Through Science and Engineering, 2011, pp. 578–585.

A. Scott and M. G. Alexander, “The influence of binder type, cracking and cover on corrosion rates of steel in chloride-contaminated concrete,” Mag. Concr. Res., vol. 59, no. 7, pp. 495–505, 2007.

S. Bhaskar, R. Gettu, B. H. Bharatkumar, and M. Neelamegam, “Studies on chloride induced corrosion of reinforcement steel in cracked concrete,” SDHM Struct. Durab. Heal. Monit., vol. 7, no. 4, pp. 231–251, 2011.

J. Pacheco, “Corrosion of steel in cracked concrete” Delft University of Technology, Netherlands, 2015.

M. Şahmaran and İ. O. Yaman, “Influence of transverse crack width on reinforcement corrosion initiation and propagation in mortar beams,” Can. J. Civ. Eng., vol. 35, no. 3, pp. 236–245, 2008.

G. Li, M. Boulfiza, and R. Evitts, “On the subtilities of rebar corrosion behaviour in cracked concrete,” Cem. Concr. Compos., vol. 160, no. March, p. 106038, 2025.

C. Martens, R. Caspeele, E. Verstrynge, C. Martens, R. Caspeele, and E. Verstrynge, “Exploring the Effects of Mechanical Cracking on the Corrosion Rate in Reinforced Concrete,” in Proceedings of the CACRCS days 2025. Presented at the CACRCS days 2025, Capacity Assessment of Corroded Reinforced Concrete Structures: from research to daily engineering evaluation, 2025.

C. GU, Y. Guang, and W. Sun, “A review of the chloride transport properties of cracked concrete: experiments and simulations,” J. Zhejiang Univ. Sci. A, vol. 16, no. 2, pp. 81–92, 2015.

Y. Cheng, Y. Zhang, Y. Jiao, and J. Yang, “Quantitative analysis of concrete property under effects of crack, freeze-thaw and carbonation,” Constr. Build. Mater., vol. 129, pp. 106–115, 2016.

Q. Deng, Z. Wang, S. Li, and Q. Yu, “Salt scaling resistance of pre-cracked ultra-high performance concrete with the coupling of salt freeze-thaw and wet-dry cycles,” Cem. Concr. Compos., vol. 146, no. June 2023, p. 105396, 2024.

ASTM, “ASTM Standard C876,” in Annual Book of ASTM Standards, West Conshohocken, USA: ASTM, 2015, pp. 1–8.

D. A. Koleva, J. H. W. de Wit, K. van Breugel, Z. F. Lodhi, and G. Ye, “Investigation of Corrosion and Cathodic Protection in Reinforced Concrete,” J. Electrochem. Soc., vol. 154, no. 5, p. C261, 2007.

R. G. Kelly, J. R. Scully, D. W. Shoesmith, and R. G. Buchheit, Electrochemical Techniques in Corrosion Science and Engineering, vol. 18. 2003.

J. P. Broomfield, Corrosion of Steel in Concrete: Understanding, Investigation and Repair. London, UK: E&FN Spon, 1997.

M. Otieno, H. Beushausen, and M. Alexander, “Chloride-induced corrosion of steel in cracked concrete - Part II: Corrosion rate prediction models,” Cem. Concr. Res., vol. 79, pp. 386–394, 2016.

M. Stern and A. L. Geary, “Electrochemical Polarization,” J. Electrochem. Soc., vol. 104, no. 9, p. 559, 1957.

C. Andrade and C. Alonso, “Corrosion rate monitoring in the laboratory and on-site,” Constr. Build. Mater., vol. 10, no. 5 SPEC. ISS., pp. 315–328, 1996.

J. A. Gonzalez, J. M. Miranda, and S. Feliu, “Considerations on reproducibility of potential and corrosion rate measurements in reinforced concrete,” Corros. Sci., vol. 46, no. 10, pp. 2467–2485, 2004.

S. Feliu, J. A. González, J. M. Miranda, and V. Feliu, “Possibilities and problems of in situ techniques for measuring steel corrosion rates in large reinforced concrete structures,” Corros. Sci., vol. 47, no. 1, pp. 217–238, 2005.

G. Song, “Theoretical analysis of the measurement of polarisation resistance in reinforced concrete,” Cem. Concr. Compos., vol. 22, no. 6, pp. 407–415, 2000.

J. Marchand, M. Jolin, and Y. Machabee, “Deicer salt scaling resistance of supplementary cementing material concrete: Laboratory results against field performance,” in Cement Combinations for Durable Concrete: Proceedings of the International Conference, 2005, pp. 579–590.

B. Savija, “Experimental and Numerical Investigation of chloride ingress in cracked concrete” Delft University of Technology, Netherland, 2014.

M. Ismail and M. Ohtsu, “Corrosion rate of ordinary and high-performance concrete subjected to chloride attack by AC impedance spectroscopy,” Constr. Build. Mater., vol. 20, no. 7, pp. 458–469, 2006.

B. Díaz, X. R. Nóvoa, and M. C. Pérez, “Study of the chloride diffusion in mortar: A new method of determining diffusion coefficients based on impedance measurements,” Cem. Concr. Compos., vol. 28, no. 3, pp. 237–245, 2006.

S. J. Ford, J. D. Shane, and T. O. Mason, “Assignment of features in impedance spectra of the cement-paste/steel system,” Cem. Concr. Res., vol. 28, no. 12, pp. 1737–1751, 1998.

M. F. Montemor, A. M. P. Simoes, and M. M. Salta, “Effect of fly ash on concrete reinforcement corrosion studied by EIS,” Cem. Concr. Compos., vol. 22, no. 3, pp. 175–185, 2000.

J. P. Broomfield, Uhlig ’ S Corrosion Handbook, Third. Hoboken, New Jersey: John Wiley and sons, inc., 2011.

C. Andrade, M. C. Alonso, and J. A. Gonzalez, “An initial effort to use the corrosion rate measurment for estimating rebar durability,” in Corrosion rates of steel in concrete, ASTM STP 1065, N. S. Berke, V. Chaker, and D. Whitning, Eds. Philadelphia, USA: ASTM, 1990, pp. 29–37.

P. Locoge, M. Massat, J. P. Olliver, and C. Richet, “Ion Diffusion in microcracked concrete,” Cem. Concr. Res., vol. 22, pp. 431–438, 1992.

X. Wang, M. Ba, B. Yi, J. Liu (2024) Experimental and numerical investigation on the effect of cracks on chloride diffusion and steel corrosion in concrete, Journal of Building Engineering, 86, 108521-108546. https://doi.org/10.1016/j.jobe.2024.108521

Downloads

Published

17-11-2026

Issue

Section

Scientific paper