Choosing the procedure for repair of damaged arm at an unicate desk lamp

Authors

  • Zoran Karastojković Society for Ethics and Evaluation in the Arts and Sciences, Belgrade Author
  • Dragan Stojiljković SPIT, Bošnjace Author
  • Suzana Polić National Museum in Belgrade, Belgrade Author

DOI:

https://doi.org/10.5937/zasmat2204381K

Keywords:

damage analysis, repairing methods, renforcing, sticking of broken parts

Abstract

Repair of any unicate artefact always requires the challenge and however demands for high level of knowledge & experience in this field, at the same level conservation works. Those demands are regarding not only on visual appearance, it is intended to stain unchainched other properties, even to question of strength, either it is an artistic piece, also the possibility of lowering the corrosion resistance, after the repair works have done. Here in details are analysed possible solutions for repairing of one broken arm when an unicate lamp unintentionaly is damaged. The used bulk material of the lamp is not available for using a kind of welding or soldering procedures, firstly that those methods will markably change the surface properties of the repaired zone. So, the repairing is provided by combining two methods: reinforcing with semi-hard aluminum wire and two component glue.

References

Alov, A. (1964) Osnovi teorii processov svarki i pajki. Moskva, p. 5-33

Belopuhov, A.K., Bekker, M.B., Zaslavskij, M.L., Ignatenko, J.G., Korotkov, R.A., Moskvin, P.P., Neazorov, J.V. (1975) Litje pod davleniem. Moskva: Mašinostroenije, p. 28-72

Beljčenko, G.I., Gubeenko, S.I. (1987) Osnovi metallografii i plastičeskoj deformacii stalji. Kiev-Doweck: Viščajaškola, p.42-119

Bogojavljenskij, K.N., Žolobov, V.V., et al. (1973) Obrabotka cvetnih metallov i splavov davlenijem. Moskva, p. 217-434

Ivanic, Lj. (2000) Casting of metals. Bor, Serbia: University of Belgrade - Technical faculty Bor, in Serbian, University book, p. 83-127

Karastojković, Z. (2020) Izveštaj CIK-a. br. 10/31 od 04.3.2020.g

Karastojković, Z. (2016) Površinska zaštita metala. Beograd, Novi Beograd: Visoka tehnička škola strukovnih studija, p.79-100

Karastojković, Z.M., Polić, S.R., Čubrilović, S.B., Jovanović, D.N., Janjušević, Z.V., Patarić, A.S. (2018) Corrodive cracks from flux residuals after brazing of thin leaves at an artistic desk lamp.Zaštita materijala, vol. 59, br. 3, str. 454-458

https://doi.org/10.5937/zasmat1803454K

Kočovski, B. (1999) Metallurgy of non-ferrous alloys II. Bor, Serbia: University of Belgrade - Technical faculty Bor, in Serbian, p. 141-156

Laško, S.V., Laško, N.F., et al. (1983) Proektirovanie tehnologiji pajki metalličeskih izdeljij. Moskva: Metallurgija, p. 34-57

Maljutina, T.M., Konjkova, O.V. (1988) Analitičeskij kontrolj v metallurgiji cvetnih i retkih metallov. Moskva: Metallurgija, p.49-237

Marković, S., Radovanović, V., Kamberović, Ž. (2005) Artistic's casting. Beograd: Klasad.o.o, in Serbian, p. 11-68

Petrić, S., Polić, S., Jovanović, D., Ilić, N., Živković, V., Džikić, V. (2015) Konzervacija srebrnog pojasa tipa Mramorac. Beograd: Centralni institut za konzervaciju u Beogradu, p. 5-27

Vudraf, D., Delčar, T. (1989) Sovremenie metodi issledovanija povrhnosti. Moskva: MIR, prevod sa engleskog, p.101-250

Zavod za zavarivanje (2016) Izveštaj br. 126.041. Beograd

Downloads

Published

15-12-2022

Issue

Vol. 63 No. 4 (2022)

Section

Articles

License

Copyright (c) 2022 CC BY 4.0 by Authors

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.